| ■Contents of modification (H21./G21./F21./E21. -> H23./G23./F23./E23.)
 File checksum command results in an error when downloading a HEX file
LED indicator does not glow red if execution of EPV command results in an error
Addition of specifications to cope with a bug in uPD70F3035A rank M
GUI software V2.16
|
(EXE file) |
Farm ware V1.35
|
(EXE file) |
■Contents of modification (G20./F20./E20. -> G21./F21./E21.)
Bug related to power supply detection function at VDD pin
Bug in LCD display
Addition of function for selecting enable/disable of power supply detection function at VDD pin (addition of specification)
Modification of specification so as not to supply VDD2 when output voltage at VDD2 pin is set to 2.0 V or lower (modification of specification)
Modification of display of [Download] menu and [Upload] menu (modification of specification)
Change of default settings of File Checksum (modification of specification)
■Contents of modification (E18./F18./G19. -> G20./F20./E20.)
Bug in Read command when UARTis used for USB communication
Addition of 9 MHz to clocks supplied from FL-PR4 (addition of specification)
Modification of percentage display when a verify error occurs in block mode with single-power-supply flashmemory microcontroller
(modification of specification)
■ Contents of modification (F17./E17.->F18./E18./G19.)
Fixing a bug in communication cannot be performed after firmware upgrade.
Fixing a bug in output from SO/TxD, RESET, SCK pins when VDD (VDD2) output is turned off.
Deletion of READ command in standalone mode. (modification of specification)
Modification of LCD display for Option Setting menu in standalone mode (modification of specification)
Addition of Progarea size display (addition of specification)
Support of single-wire UART communication (78K0S/Kx1+) (addition of specification)
■Contents of modification (E10./E11./F13./F14/F15.F16./E16.->F17./E17.)
Fix of bug in address display in Boot block setting .
Fix of bug in Address display in Block/Area.
Fix of the bug in execution of Update Firmware with USB2.0.
Fix of the bug in cancel operation in Security flag Setting confirmation dialog box.
Fix of the bug in CLK output.
Modification of [Upload…] menu specifications (3) (addition of specification)
Modification of default communication speed (modification of specification)
Addition of function to display Checksum command execution result on LCD (addition of specification)
■Contents of modification (E10./E11./F13./F14/F15.->F16./E16.)
Addition of subcommands to Read command (addition of specification)
Addition of Get Security Settings command (addition of specification)
Addition of Boot block cluster setting function (addition of specification)
<Security Setting> Addition of Read command disable function (addition of specification)
<Security Setting> Addition of Boot block cluster reprogramming disable function (addition of specification)
<Security Setting> Addition of Reset vector (addition of specification)
<File checksum> Addition of Arithmetic checksum (16 bits) and modification of GUI display (addition of specification)
Modification of Checksum specification at Download or EPV (addition of specification)
Addition of 57,600 bps, 115,200 bps, 128,000 bps to GUI baud rate selection menu for UART communication (addition of specification)
Modification of target power supply detection function (addition of specification)
Modification of [Upload…] menu specifications (1) (addition of specification)
Modification of [Upload…] menu specifications (2) (addition of specification)
Modification of [Logging] menu specifications (addition of specification)
Modification of GUI specification when host machine is shut down (addition of specification)
Modification of specification when Disable Chip Erase is selected and popup message is cancelled (addition of specification)
The last address input for file upload differs from the one actually executed
Bug in Address display in Block/Area
■Contents of modification (E8./E9.->E10./E11./F13./F14/F15.)
Bug in Motorola S format HEX download <Firmware>
■Contents of modification (D6.->E8./E9.)
Bug in SIO-H/S communication mode <Firmware>
Bug in voltage output when power supply is turned on/off <Hardware>Note1
Bug in checksum command of dual-power-supply flash memory microcontroller on stand-alone mode <Firmware>
Note1
Modifying this problem needs upgrading a hardware. Please ask distributor or agent about upgrading a hardware. |
■Contents of modification (C5.->D6.)
Restriction Security function on single-power-supply flash memory microcontroller
Bug in setting checksum command in dual-power-supply flash memory microcontroller
Modification of specification of Multiply rate input form
Addition of the number display of VPP/FLMD pulses in Communication PORT select
■Contents of modification (C4.->C5.)
Bug in parallel I/F communication
Restriction on checksum command in dual-power-supply flash memory microcontroller Note2
Bug in communication port selection in single-power-supply flash memory microcontroller
Bug in display of checksum command Note2
Bug in upload
Modification of specification of baud rate selection in UART communication mode
Bug in upgrading firmware
■Contents of modification (C2./C3.->C4.)
Modification on the Restriction1 about the single power supply flash microcomputer.
Modification on the address display problem of HEX Editer.
Modification on the command display problem1in use of USB/IF.
Modification on the problem of USB I/F on Windows2000 SP2.
Support of the changing Program area Icon.
Modification on the command display problem2 in use of USB/IF.
Contents of modification (B1.->C2./C3.)
The parameter files currently offered by NEC Web Site became usable. (The past parameter files(xxxx-ES2.PRM) cannot be used.)
Modification on the automatic selection error of signature.
Modification on the IIC communication error.
Modification on the USB communication error.
Modification on the baud rate error at Uploading.
Modification on the abort error.
It supported to the single power supply flash microcomputer. |
